Видео

Armando.nieblapasswordpasswordpasswordpasswordpasswordpasswordpasswordoasswordpasswordpasswordpsswordpasswordpassqordpassword

Do you still use this? as I would buy the duplex unit off it if you dont

Armando nieblapassqordpasswordpasswordpasswordpasswordpasswordpasswordpasswordpasswordpasswordpassqordpasswordpasswordpasswordpassword

It’s live line work glove and barrier

I am in a fever dream

💖

You don't part off between centers. That's asking for trouble. You were lucky.

no cell phones , no vaping, mind on what you are doing !

Thanks for this

well this might not get answered cause vid is so old but maybbbbbbbbe. you happen to have any info on the "nippled fitting"/ fuel inlet into this lift pump? Am converting to AN6 fittings and really need this to replace all my horrible fuel lines and leaks. (on a horribly done customized conversion yet.... HAS to be my daily driver ASAP) orrrr. do you think the nipple could be cut off, drilled out and put an NPT fitting in its place. That would be up to what is seat the check valve hits... is that up inside the fitting... or on the end of the threaded portion of this fitting where it meets up with the chamber inside the pump housing?

this is random

pretty basic line work stuff .. now do it in the rain or 60 below wind chill

Why let the groundman be on underneath while installing crossarms and other materials. Im just saying, please dont take it no other way, stay safe 🙏🏽

Did you mix oil in gas help please

Gas mix please

What is a point of having that roof rack and don't share the brand and place where you bought it? I have a same car as you and I want a same roof rack to buy and avoid drilling when it can be attached to the gutter. Please provide me with info about it.

You did a great job.

The thing to realise is those lines around them are still active and powered while they are working! that why all the rubber suits and arms sleeves as well as the rubber line covers. 12,000 volts or so....

Those don’t look like class 4 gloves.

Your workbench looks just like mine, after I cleaned it. I'm a retired CB & Marine Radio technician; but can't stop playing with these things. I've been licensed since the 70s... Also have a commercial license. Good video!

Don’t you guys put split bolts below your eye bolts to keep your poles from splitting because of the angle and the anchor

Can I use mobile ham antenna for cb and how to cut it or lengthen it

The description is perfect

"Can I talk now?" ? Let's hear what he has to say.

these ppl are brave to be doing this job, i wouldn't do it bc im afraid of heights n getting zapped, lol!!

no admission to the circus, when do i get to go, lol!!

Can you tell me please if these D7s are right or left handed propellers?

Such a clean work. Thank you so much for working hard to make our life easier. Take care.

HELLO HOW ARE YOU ENG. I HAVE A #2170 BUT I LOST THE SOFTWARE FOR ITS OPERATION, CAN YOU HELP ME GET THE DRIVES

do you still play radio at all?

imagine programing a browser to simply use the radio as a modem...

Wow. Could you provide a few steps you followed? I only produced 3d parts with fusion 360 so far in complex shapes.

This is one of the best videos on linemen I've seen and thanks who I consider are Frontline workers great close up enjoyed it very educational almost professional video

very cool, i loved hopping back in the time machine for this one 73

I was there, it was great & fun. I came with a few bus's from Ann Arbor.

Wrong blade for ripping, you have a cross cut blade on. No anti-kick on your work and nothing to hold your work past the cut...... no support at the exit side, the board tilts up against the blade and it will send that board flying at you. Wrong way to operate this arm saw, it is NOT safe for your viewers. I do not get it... two passes for one cut?. that burnt mark on you cut piece is telling me that blade is not adjusted right and also the table not being parallel to the arm. You look stiff and afraid. You should not be ripping this way on a radial arm saw. take the video off.

It's good to see Woodprix have new instructions to save my money and energy to build it.

I hate when people take pictures or record me or even watch when I’m in the bucket

Интересная приспособа! Возьму на заметку!

You could have made that in one cut easy. Nice set up.

Pretty Cool,cant seem to get up there to see her.

38 Surrey Road Wanganui New Zealand I ordered a power pole for Ryan palazzo

nice idea . i can not find part two?

Good form mate. Do up a favor, drop the anti kick paw down. We would hate to see you get a bruise on your gut or send a piece of wood through the garage wall. And as for the comment above feeding from the wrong side- you need to learn what a radial arm saw is and does and the correct way to use them before telling someone their using it wrong. It would be absolute stupidity to feed a board in the downward rotation of the blade. The only issue in this video is he didn't use the anti kick paw.

Nothing like my Mac22.

Good hack

I’m gonna try this with my friend on an ssb cb

What kind of oil did you use? Do you remember ?

Immhave one tese insulator but never know is have a type brown

I Hi.. i have a craftsmsn router keeps turning off due to sparks..i took apart and filed the commutator good on a lathe and then i flattened the brushes good and now it works a bit better but powers off at high rpm setting...sparks...anyone have any suggestions..brushes are about 1/2 in long